Sitemap

Строительные материалы №11Construction materials №11

Table of contents

Д.В. ОРЕШКИН, д-р техн. наук, Московский государственный строительный университет
D. V. ORESHKIN, Doctor of Technical Sciences, the Moscow State Building University

Рассмотрены проблемы строительного материаловедения и нормативной базы, которые должны непрерывно развиваться и дополняться результатами исследований ученых и специалистов-производственников. Предложены пути развития производства строительных материалов. «стр.6»

Ключевые слова: строительное материаловедение, нормативная база, производство строительных материалов.

The problems of the building materiology and normative basis which must be developed continuously and supplemented with the results of research conducted by scientists and specialists-production workers are considered. The ways of the development of building materials production are proposed. «P.6»

Key words: building materiology, normative basis, building materials production.
О.Н. КРАШЕНИННИКОВ, д-р техн. наук, Т.П. БЕЛОГУРОВА, канд. техн. наук, Институт химии и технологии редких элементов и минерального сырья им. И.В. Тананаева Кольского научного центра РАН (Апатиты Мурманской обл.); Л.И. МАЛЬЦЕВ, д-р техн. наук, Институт теплофизики им. С.С. Кутателадзе Сибирского отделения РАН (Новосибирск); И.В. КРАВЧЕНКО, директор ООО «Завод стеновых блоков» (Новосибирск)
O.N. KRASHENINNIKOV, Doctor of Technical Sciences, T.P. BELOGUROVA, Candidate of Technical Sciences, the I.V. Tanaev Institute of Chemistry and Technology of Rare Elements and Mineral Raw Materials, the Kola Science Centre of the Russian Academy of Sciences, (Apatity, Murmansk Reg); L.I. MALTSEV, Doctor of Technical Sciences, the S. S. Kutateladze Institute of Thermophysics, Siberian Branch of the Russian Academy of Science(Novosibirsk); I.V. KRAVCHENKO, Director, OOO “Zavod stenovykh blokov” (Novosibirsk)

Изучен химический и минеральный состав, структурные особенности и основные физико& механические свойства, выполнена радиационно&гигиеническая оценка золоотходов, полученных в результате сжигания водоугольного топлива на основе кузнецкого каменного угля в теплогенерирующей установке ООО «Завод стеновых блоков» (Новосибирск). Результаты проведенных исследований свидетельствуют о перспективности использования этих золоотходов в качестве добавки в бетоны. «стр.10»

Chemical and mineral compositions, structural peculiarities and basic physico-mechanical properties are studied, radiation-hygienic assessment of ash waste as a result of the combustion of water-carbon fuel on the basis of Kuznetsk coal in the heat-generating plant of OOO “Zavod stenovykh blokov”(Novosibirsk) is made. Results of the studies confirm the perspectivity of using this ash waste as an additive to concrete. «P.10»
В.И. КАЛАШНИКОВ, д-р техн. наук, К.Н. МАХАМБЕТОВА, канд. техн. наук (techbeton@pguas.ru), Пензенский государственный университет архитектуры и строительства
V.I. KALASHNIKOV, Doctor of Technical Sciences, K. N. MAKHAMBETOVA, Candidate of Technical Sciences (techbeton@pguas.ru), the Penza State University of Architecture and Building

Приведены результаты изучения коррозии пористых цементно-песчаных образцов бетона в агрессивной среде 5% раствора сульфата магния. Для снижения коррозии применяли как отдельно метилцеллюлозу МЦ-С, редиспергируемые латексные порошки РАV-29 и РАV-30, стеарат цинка, так и комплексную добавку, содержащую все перечисленные гидрофобизаторы. Образцы, модифицированные комплексными добавками, имеют высокий коэффициент коррозионной стойкости. «стр.12»

Ключевые слова: агрессивная среда, коррозия бетона, гидрофобизация.

Results of the study of corrosion of porous cement-sand samples of concrete in the aggressive medium of 5% solution of magnesium sulphate are presented. To reduce the corrosion they used separately methyl cellulose МЦ-С, redispersed latex powders РАV-29 and РАV-30, zinc stearate and also a complex additive containing all enumerated hydrophobic agents. The samples modified with complex additives have the high coefficient of corrosion resistance. «P.12»

Key words: corrosive medium, corrosion of concrete, hydrophobization.
В.С. ИЗОТОВ, д-р техн. наук, Р.А. ИБРАГИМОВ, инженер (Rusmag007@yandex.ru), Казанский государственный архитектурно-строительный университет
V.S. IZOTOV, Doctor of Technical Sciences, R.A. IBRAGIMOV, engineer (Rusmag007@yandex.ru), the Kazan State Architectural and Building University

Рассмотрены особенности влияния гиперпластификаторов на основе эфиров поликарбоксилатов на свойства цементного камня, раствора и бетона, а также на кинетику тепловыделения и контракцию цементного теста. «стр.14»

Ключевые слова: добавки, гиперпластификаторы, тяжелый бетон.

Features of the influence of hyper-plasticizers on the basis of polycarboxylates ethers on the properties of cement stone, mortar and concrete as well as on the kinetics of heat emission and concentration of cement paste are considered. «P.14»

Key words: additives, hyper-plasticizers, heavy concrete.
С.П. СИВКОВ, канд. техн. наук, С.Ш. ДАУЛЕТБАЕВА, инженер, Российский химико-технологический университет им. Д.И. Менделеева (Москва)
S.P. SIVKOV, Candidate of Technical Sciences, S.Sh. DAULETBAEVA, engineer, D.I. Mendeleev University of Chemical Technology of Russia (Moscow)

Установлено, что модифицирование парафиновых дисперсий поверхностно&активными веществами на основе акриловых полимеров увеличивает их стабильность в щелочной среде твердеющего цемента и способствует более равномерному распределению парафиновой пленки в структуре затвердевшего цементного камня. Использование модифицированных парафиновых дисперсий в составе цементных растворов и бетонов позволяет значительно повысить морозостойкость и коррозионную стойкость бетона за счет снижения скорости массопереноса в материале. «стр.18»

Ключевые слова: парафиновые дисперсии, коррозионная стойкость, морозостойкость бетона.

It is established that the modification of paraffin dispersions with surfactants on the basis of acrylic polymers improves their stability in the alkaline medium of the hardening cement and contributes to the more uniform distribution of paraffin film in the structure of cement stone hardened. The use of the modified paraffin dispersions in the composition of cement mortar and concretes makes it possible to considerably improve frost resistance and corrosion resistance owing to reduction of the speed of mass transfer in the material. «P.18»

Key words: paraffin dispersions, corrosion resistance, frost resistance of concrete.
С.А. ГОЛУНОВ, инженер, А.П. ПУСТОВГАР, канд. техн. наук, С.А. ПАШКЕВИЧ, Е.В. ДУДЯКОВ, инженеры, Московский государственный строительный университет
S.Ya. GOLUNOV, engineer, A.P. PUSTOVGAR, Candidate of Technical Sciences, S.A. PASHKEVICH, E.V. DUDYAKOV, engineers, the Moscow State Building University

Приведены основные характеристики материалов фасадной композиционной системы теплоизоляции с тонким штукатурным слоем. Показано назначение каждого слоя и испытываемые нагрузки. Представлена европейская нормативная база для данных систем. Описаны основные требования, предъявляемые к системам нормативным документом ETAG004 EOTA. «стр.21»

The basic characteristics of the materials of façade composition systems of heat insulation with the thin plaster layer are given. The purpose of each layer and experienced loads are shown. European normative base for these systems is presented. The basic requirements of the normative document ETAG004 EOTA to the systems are described. «P.21»
Е.А. ШЛЯХОВА, канд. техн. наук, А.Ф. АКОПЯН, инженер (a-lex-an-der@yandex.ru), Ростовский государственный строительный университет
E.A. SHLYAKHOVA, Candidate of Technical Sciences, A.F. AKOPYAN, engineer (a_lex_an_der@yandex.ru), the Rostov State Building University

На примере исследования гранулированного шлака и несиликатного щелочного компонента, являющегося побочным продуктом химической промышленности, рассмотрено использование математических моделей для оценки границ применимости сырьевых материалов для производства шлакощелочных вяжущих заданной марочной прочности. «стр.28»

Ключевые слова: шлакощелочные вяжущие, математическое планирование эксперимента, марочная прочность, границы применимости сырья.

The use of mathematical models for evaluating the limits of the applicability of raw materials for production of slag-alkali binders of the preset grade strength is illustrated by an example of study of granulated slag and non-silicate alkali component which is a by-product of the chemical industry. «P.28»

Key words: slag-alkali binders, mathematical planning of experiment, grade strength, limits of raw material applicability.
Б.М. РУМЯНЦЕВ, д-р техн. наук, А.В. ОРЛОВ, инженер (xtz@mail.ru), Московский государственный строительный университет
B.M. RUMYANTSEV, Doctor of Technical Sciences, A.V. ORLOV, engineer (xtz@mail.ru), the Moscow State Building University

Работа отражает исследование и установление зависимостей при разработке материалов с повышенной сорбционной способностью и ионообменными процессами, обеспечивающих длительное функционирование при очистке воздуха. В основу рабочей гипотезы работы положен принцип молекулярных сит, которые избирательно поглощают вредные вещества, имеют сильно развитую поверхность и широко представлены группой природных цеолитов. В качестве перспективного направления развития работы по созданию гипсоцеолитовых материалов выбрано изготовление лицевых элементов подвесных потолков, без которых не строится практически ни одно современное здание. «стр.30»

Ключевые слова: цеолиты, сорбционная способность материалов, поризованные гипсовые материалы, декоративно-акустические материалы.

The article covers the study and establishment of dependences in the course of development of materials with improved sorption capacity and ion exchange processes ensuring long-term operation at air cleansing. The principle of molecular sieves absorbing selectively harmful substances, having a well-developed surface and widely presented by the group of natural zeolites is assumed as the basis of the working hypothesis of this work. The production of exterior elements of suspended ceilings, practically, no one modern building is constructed without them, is selected as a perspective trend in development of the work aimed at the creation of zeolite materials. «P.30»

Key words: zeolites, sorption capacity of materials, porous gypsum materials, decorative-acoustic materials.
7–8 октября 2010 г. в Москве состоялась конференция «Высокофункциональный бетон», организованная Центром бетонных технологий (Санкт-Петербург) и Ассоциацией «Железобетон» (Москва) при участии Дрезденского Технического Университета и Национального исследовательского университета МГСУ. По традиции формат конференций Центра бетонных технологий включал мастер-класс, который провел профессор Дрезденского Университета, директор института строительных материалов В.С. Мещерин. Модератором конференции выступил вице-президент Ассоциации «Железобетон», профессор кафедры технологии вяжущих веществ и бетонов МГСУ В.Р. Фаликман. «стр.34»

The Conference “High Performance Concrete” organized by the Center of concrete technologies (St. Petersburg) and the “Reinforced Concrete” Association with the participation of the Dresden Technical University and the National research university of MGSU took place in Moscow on 7 – 8 October, 2010. By tradition the format of conferences of the Center of concrete technologies included a master-class conducted by V.S. Meshcherin, professor of the Dresden University, director of the Institute of building materials. V. R. Falikman, vice-president of the “Reinforced Concrete” Association, professor of the department of technology of binding substances and concretes of MGSU was a moderator of the conference. «P.34»
К.С. ИВАНОВ, канд. техн. наук, Институт криосферы Земли СО РАН (Тюмень) ; С.С. РАДАЕВ, канд. техн. наук, Тюменский государственный архитектурно-строительный университет
K.S. IVANOV, Candidate of Technical Sciences, Institute of Earth's Cryosphere, Russian Academy of Sciences, Siberian Branch (Tyumen); S.S. RADAEV, Candidate of Technical Sciences, the Tyumen State Architectural and Building university

Установлена возможность получения ячеистого теплоизоляционного материала плотностью 290–580 кг/м3, прочностью при сжатии 1,7–7,8 МПа и теплопроводностью 0,08–0,14 Вт/(м·К) из смеси диатомита и 40% раствора NaOH путем обжига при 775оС. Показано, что гидротермальная обработка смеси при 95оС ускоряет процесс выщелачивания аморфного SiO2, а образующиеся при этом растворимые щелочные силикаты способствуют вспучиванию смеси при обжиге и снижают плотность. Оптимальная продолжительность выщелачивания составляет 30 минут, что соответствует выходу SiO2, равному 42,5% от массы сухого диатомита и силикатному модулю m = 3,15. Роль вспучивающего агента играет кристаллизационная вода, выделяющаяся из сопутствующих глинистых минералов. По структуре и свойствам материал близок к пеностеклу. «стр.36»

The possibility of producing the cellular heat insulating material of 290-580 kg/m³ density, 1.7 – 7/8 MPa compress strength, 0.08 – 0.14 Wt/(m•K) heat conductivity from a mix of diatomite and 40% solution of NaOH by calcination at 77 °C has been established. It is shown, that the hydrothermal treatment of the mix at 95 °C accelerates the leaching of amorphous SiO2, and the soluble alkali silicates generated in the course of it contribute to the swelling of the mix during the calcination and reduce the density. The optimal duration of leaching is 30 minutes, corresponding to a yield of SiO2, equal 42.5% of dry diatomite and silica modulus m = 3.15. The crystal water exuding from associated clay minerals plays a role of a swelling agent. The structure and properties of the material close to the glass foam. «P.36»
В сентябре–октябре 2010 г. состоялся ряд конференций, которые, наверное, было бы сложно объединить в один обзор, если бы не наметившиеся тенденции развития строительного материаловедения. «стр.38»
Д.Г. КИСЕЛЕВ, инженер (korolev_ev@rambler.ru), Е.В. КОРОЛЕВ, д-р техн. наук, Н.А. ПРОШИНА, канд. техн. наук, Пензенский государственный университет архитектуры и строительства; А.И. АЛЬБАКАСОВ, канд. техн. наук, Оренбургский государственный университет
D.G. KISELEV, engineer (korolev_ev@rambler.ru), E.V. KOROLEV, Doctor of Technical Sciences, N.A. PROSHINA, Candidate of Technical Sciences, the Penza State University of Architecture and Building; A.I. ALBAKASOV, Candidate of Technical Sciences, the Orenburg State University

Исследовано влияние термообработки наполнителя и введения аппретирующих веществ на свойства тальксодержащих серных строительных материалов. Показано, что термообработка талька при 800–900оС приводит к повышению прочности серных композитов, а аппретирование наполнителя способствует повышению их водостойкости, снижению водопоглощения и истираемости. «стр.40»

The influence of thermal treatment of a filler and introduction of stiffeners on properties of talc containing sulfuric building materials is studied. It is shown that thermal treatment of talc at 800-900°C leads to improvement of sulfuric composites strength, and stiffening of the filler contributes to the improvement of their water-resistance, reduction of water absorption and attrition. «P.40»
Е.В. ГОНЧИКОВА, канд. техн. наук (egonchikova@mail.ru), Н.В. АРХИНЧЕЕВА, канд. хим. наук, Е.В. ДОРЖИЕВА, инженер, А.В. ЦЫРЕМПИЛОВА, инженер, Восточно-Сибирский государственный технологический университет (Улан-Удэ, Республика Бурятия)
E.V. GONCHIKOVA, Candidate of Technical Sciences (egonchikova@mail.ru), N.V. ARKHINCHEVA, Candidate of Chemical Sciences, E.V. DORZHIEVA, engineer, A.V. TSYREMPILOVA, engineer, the East Siberian State Technological University (Ulan-Ude, The Republic of Buryatia)

Приведены результаты исследования влияния золей гидроксидов металлов в вяжущих композициях на основе безводных силикатов натрия. Рассмотрены различные композиции с минеральными тонкомолотыми наполнителями с использованием местных горных пород – дунитов, базальтов, сынныритов и вулканических шлаков, а также зол. «стр.42»

Ключевые слова: силикат-натриевые композиционные вяжущие, золь, вулканический шлак, сыннырит, дунит.

Results of the study of the effect of metal hydroxides sols in binding compositions on the basis of water-free sodium silicates are presented. Variuos compositions with mineral finely-ground fillers using local rocks - dunites, basalts, synnyrites, volcanic slags, and sols - are considered. «P.42»

Key words: silicate-sodium composition binders, sol, volcanic slag, synnyrite, dunite.
Т.К. УГЛОВА, старший научный сотрудник (labmineral@mail.ru), С.Н. НОВОСЕЛОВА, научный сотрудник (labmineral@mail.ru), О.С. ТАТАРИНЦЕВА, д-р техн. наук, Институт проблем химико-энергетических технологий Сибирского отделения РАН (г. Бийск Алтайского края)
T.K. UGLOVA, senior research worker (labmineral@mail.ru), S.N. NOVOSELOVA, research worker (labmineral@mail.ru), O.S. TATARINTSEVA, Doctor of Technical Sciences, Institute for Problems of Chemical & Energetic Technologies of the Siberian Branch of the Russian Academy of Sciences (Biysk, Altai krai)

Рассмотрены технологические приемы изготовления экологически чистых теплоизоляционных материалов – пеносиликатов на основе жидкого натриевого стекла и минеральных наполнителей: микрокальцита, аэросила, каолина. Показана возможность изготовления пеносиликата с высокими техническими свойствами без стадии грануляции и применения закрытых герметичных форм. «стр.44»

Ключевые слова: пеносиликат, пористость, наполнитель, плотность, теплопроводность, водопоглощение.

Technological methods of the production of ecologically pure insulation materials, foamed silicates based on liquid sodium glass and mineral fillers - microcalcite, aerosil, kaolin, are considered. The possibility of manufacturing the foamed silicate with high technical properties without the stage of granulation and usage of the closed hermetical forms is shown. «P.44»

Key words: foamed silicate, porosity, filler, density, heat conductivity, water absorption.
А.П. ЗУБЕХИН, д-р техн. наук, Н.Д. ЯЦЕНКО, канд. техн. наук, Е.В. ФИЛАТОВА, канд. техн. наук, В.И. БОЛЯК (v.bolyak@mail.ru), К.А. ВЕРЕВКИН, инженеры, Южно-Российский государственный технический университет (Новочеркасский политехнический институт)
A.P. ZUBEKHIN, Doctor of technical Sciences, N.D. YATSENKO, Candidate of Technical Sciences, E.V. FILATOVA, Candidate of Technical Sciences, V.I. BOLYAK (v.bolyak@mail.ru), K.A. VEREVKIN, engineers, the South Russian State Technical University (the Novocherkask Polytechnical Institute)

Установлено влияние химико-минералогического состава глин на технологические, послеобжиговые и декоративные свойства керамического кирпича. Изучены зависимости коэффициента отражения и цвета фаз, кристаллизующихся в кирпиче, от содержания оксида железа. «стр.47»

Ключевые слова: фазовый состав, свойства керамических материалов, керамический кирпич, глина.

The influence of the chemical-mineralogical composition of clays on technological, afterburning and decorative properties of ceramic brick is established. Dependencies of the reflection coefficient and the colour of phases crystallized in the brick on the content of iron oxide are studied. «P.47»

Key words: phase composition, ceramic materials properties, ceramic brick, clay.
Группа КНАУФ СНГ – крупнейший производитель высококачественных строительных отделочных материалов представляет на российском рынке новую интерактивную систему поиска комплектных систем и расчета расхода материала «Навигатор и калькулятор КНАУФ». Интерактивная система разработана российскими специалистами КНАУФ на платформе, созданной компанией Knauf IS (Германия), и состоит из двух частей – навигатора по комплектным системам КНАУФ и калькулятора расхода строительных материалов. «стр.50»

The KNAUF CIS Group, the largest producer of high quality building finishing materials, presents on the Russian market a new interactive search system of complete systems and calculation of material consumption “Navigator and Calculator KNAUF”. The interactive system developed by Russian specialists of KNAUF on the platform created by Knauf IS (Germany), and consists of two parts: the navigator KNAUF of complete systems and calculator of building materials consumption. «P.50»
Н.Д. ЯЦЕНКО, канд. техн. наук, Южно-Российский государственный технический университет (Новочеркасский политехнический институт); Э.О. РАТЬКОВА, инженер лаборатории, «СевКавНИИСтромтехника» (Ростов-на-Дону); В.В. СЕМЧЕНКО, Н.А. СТРЕБКОВА (strebkova61@mail.ru), инженеры, Южно-Российский государственный технический университет (Новочеркасский политехнический институт)
N.D. YATSENKO, Candidate of Technical Sciences, the South Russian State Technical University (the Novocherkask Polytechnical Institute), E.O. RATKOVA, engineer of laboratory, “SevKavNIIStromtekhnila” (Rostov-on-Don); V.V. SEMCHENKO, N.A. STREBKOVA (strebkova61@mail.ru), engineers, the South Russian State Technical University (the Novocherkask Polytechnical Institute)

Приведены результаты синтеза тонкослойного покрытия из гидролизованных групп Si-OH- и замещения их катионами Li+, Na+, Ka+, Ca2+. При обжиге керамического кирпича полусухого прессования происходит заполнение и уплотнение пор поверхностного слоя. За счет спекания поверхности увеличивается прочность, и особенно морозостойкость кирпича. «стр.52»

Ключевые слова: керамический кирпич, пористость, поверхностное насыщение, комбинированные добавки.

Results of the synthesis of a thin-layer covering from hydrolized groups Si&OH& and the substitution of them with cations Li+, Na+, Ka+, Ca2+ are presented. In the course of burning of ceramic brick of semidry pressing the packing and compaction of pores of the surface layer takes place. Strength and frost-resistance of brick are improved owing to surface sintering. «P.52»

Key words: ceramic brick, porosity, surface saturation, combined additives.
М.Г. ГАБИДУЛЛИН, д-р техн. наук, Казанский государственный архитектурно-строительный университет; А.Н. ГАБИДУЛЛИНА, инженер (gabmah@mail.ru), Институт механики и машиностроения КазНЦ РАН (Казань)
M.G. GABIDULLIN, Doctor of Technical Sciences, the Kazan State Architectural and Building University, A.N. GABIDULLINA, engineer (gabmah@mail.ru), the Research Institute of Mechanics and Machinery of Kazan Scientific Center of the Russian Academy of Sciences( Kazan)

Исследовано изменение теплофизических свойств пористой керамики для двух различных условий (модель II и модель III) увлажнения порового пространства. Для этого по установленным экспериментальным данным рассчитаны значения термического сопротивления моделей и ограждений на их основе. Доказано, что основное влияние на изменение термического сопротивления моделей II и III при их увлажнении оказывает объем открытых пор. «стр.56»

Ключевые слова: пористая керамика, термическое сопротивление, модель порового пространства, влажность материала.

The change of thermal-physical properties of porous ceramics for two different conditions of moistening (model II and model III) of the pore space is studied. For this, the thermal resistance values of models and enclosures are calculated on the basis of the established experimental data. It is proved that the volume of open pore exerts the main influence on the change of thermal resistance of models II and III at their moistening. «P.56»

Key words: porous ceramics, thermal resistance, model of pore space, material dampness.
По материалам Международного совещания «Научные основы и современные процессы комплексной переработки труднообогатимого минерального сырья». «стр.60»
Новости «стр.62»
News «P.62»
El_podpiska СИЛИЛИКАТэкс KERAMTEX СМ_Телеграмм elibrary interConPan_2024 Тратуарная плитка